CDL General Knowledge Practice Test 9

24 free CDL General Knowledge practice questions with answers and explanations. Choose an answer to check it right away and read why. You need at least 80% correct to pass the real test.

1.During the CDL vehicle inspection test, you must:

  1. Inspect only the tires and brakes
  2. Point to or touch each item, name it, and explain what you are checking and why
  3. Hand the examiner a written checklist
  4. Watch while the examiner does the inspection
Show answer

B. Point to or touch each item, name it, and explain what you are checking and why

You must point to or touch and name the item you are inspecting, and explain to the examiner what you would inspect and why.

CDL manual, section 2.1.4.

2.When reviewing the last vehicle inspection report, you must sign it only if:

  1. You drove the vehicle the day before
  2. The vehicle is due for service
  3. No defects were found
  4. Defects were noted and certified as repaired or not needing repair
Show answer

D. Defects were noted and certified as repaired or not needing repair

The motor carrier must repair any items that affect safety and certify on the report that repairs were made or were unnecessary. You must sign the report only if defects were noted and certified to be repaired or not needed to be repaired.

CDL manual, section 2.1.5.

3.Before you check the engine compartment, make sure:

  1. The parking brake is on and/or the wheels are chocked
  2. The engine is running at high idle
  3. The cab doors are unlocked
  4. The headlights are on
Show answer

A. The parking brake is on and/or the wheels are chocked

Step 2 of the inspection starts by checking that the parking brakes are on and/or the wheels are chocked. If you tilt the cab, secure loose items first so they don't fall and break something.

CDL manual, section 2.1.5.

4.After you start the engine, oil pressure should:

  1. Stay at zero until you start driving
  2. Rise slowly over about 10 minutes
  3. Come up to normal within seconds
  4. Go to the top of the gauge
Show answer

C. Come up to normal within seconds

Oil pressure should come up to normal within seconds after the engine is started. Coolant and engine oil temperature should begin a gradual rise to the normal operating range.

CDL manual, section 2.1.5.

5.Air pressure governor cut-out is usually around:

  1. 60 to 80 psi
  2. 120 to 140 psi
  3. 90 to 100 psi
  4. 200 psi
Show answer

B. 120 to 140 psi

Pressure should build from 50 to 90 psi within 3 minutes. Then build air pressure to governor cut-out, usually around 120 to 140 psi. Know your vehicle's requirements.

CDL manual, section 2.1.5.

6.When you start the engine, the ABS light on the dash comes on and stays on. This means:

  1. The ABS is working normally
  2. The parking brake is set
  3. The trailer is not connected
  4. The ABS is not working properly
Show answer

D. The ABS is not working properly

The ABS light on the dash should come on and then turn off. If it stays on, the ABS is not working properly.

CDL manual, section 2.1.5.

7.Before you get out to check the lights in Step 4 of the inspection, you should:

  1. Set the parking brake, turn off the engine, and take the key with you
  2. Leave the engine running so the lights stay on
  3. Put the transmission in neutral and release the brakes
  4. Lock the doors with the key inside
Show answer

A. Set the parking brake, turn off the engine, and take the key with you

Make sure the parking brake is set, turn off the engine, and take the key with you. Then turn on the low beams and four-way flashers and get out of the vehicle.

CDL manual, section 2.1.5.

8.Clearance lights, identification lights and reflectors on the front of the vehicle should be:

  1. Red
  2. White
  3. Amber
  4. Blue
Show answer

C. Amber

Parking, clearance and identification lights and reflectors at the front should be clean, working and the proper color, which is amber at the front.

CDL manual, section 2.1.5.

9.On a cab-over-engine truck, during the walk-around you should check that:

  1. The cab is tilted forward
  2. The primary and secondary safety cab locks are engaged
  3. The hood is open
  4. The fifth wheel is greased
Show answer

B. The primary and secondary safety cab locks are engaged

On a cab-over-engine design, check that the primary and secondary safety cab locks are engaged.

CDL manual, section 2.1.5.

10.How can you check the stop lights during the inspection when you are alone?

  1. Apply the trailer hand brake
  2. Look at the light on the dash
  3. Pump the brake pedal from outside the cab
  4. Stop lights do not need to be checked
Show answer

A. Apply the trailer hand brake

Turn on the stop lights by applying the trailer hand brake or having a helper press the brake pedal, then get out and check them.

CDL manual, section 2.1.5.

11.Why should you secure loose items in the cab before driving?

  1. So they don't get stolen
  2. To pass a weight check
  3. To keep the cab clean
  4. They could interfere with the controls or hit you in a crash
Show answer

D. They could interfere with the controls or hit you in a crash

Secure all loose articles in the cab. They might interfere with operation of the controls or hit you in a crash.

CDL manual, section 2.1.5.

12.How do you test the parking brake during the inspection?

  1. Pull the parking brake while driving at 20 mph
  2. Push down hard on the brake pedal
  3. Set it, put the vehicle in a low gear, and gently pull forward against it
  4. Release it on a downhill grade
Show answer

C. Set it, put the vehicle in a low gear, and gently pull forward against it

Fasten your safety belt, set the parking brake, put the vehicle in a low gear, and gently pull forward against the parking brake to make sure it holds. If it doesn't hold, get it fixed.

CDL manual, section 2.1.5.

13.You test the service brakes at about 5 mph and the vehicle pulls to one side. This can mean:

  1. Brake trouble
  2. The tires are new
  3. The road is wet
  4. Normal brake behavior
Show answer

A. Brake trouble

Pulling to one side, an unusual brake pedal feel or delayed stopping action can mean brake trouble. Federal and state laws forbid operating an unsafe vehicle.

CDL manual, section 2.1.5.

14.While double clutching, you stay in neutral too long and cannot get into the next gear. You should:

  1. Force the shifter into gear
  2. Return to neutral, release the clutch, raise engine speed to match road speed, and try again
  3. Turn off the engine and restart it
  4. Skip to the highest gear
Show answer

B. Return to neutral, release the clutch, raise engine speed to match road speed, and try again

Don't try to force it. Return to neutral, release the clutch, increase engine speed to match road speed, and try again.

CDL manual, section 2.3.1.

15.Some newer vehicles use "progressive" shifting. This means:

  1. You shift only with the clutch pedal
  2. The truck shifts by itself
  3. You skip every other gear
  4. The rpm at which you shift becomes higher as you move up through the gears
Show answer

D. The rpm at which you shift becomes higher as you move up through the gears

With progressive shifting, the rpm at which you shift becomes higher as you move up in the gears. Find out what is right for the vehicle you drive.

CDL manual, section 2.3.1.

16.Looking 12 to 15 seconds ahead at highway speed means looking about:

  1. 50 feet ahead
  2. One car length ahead
  3. A quarter of a mile ahead
  4. Two miles ahead
Show answer

C. A quarter of a mile ahead

At lower speeds, 12 to 15 seconds ahead is about one block. At highway speeds, it is about a quarter of a mile.

CDL manual, section 2.4.1.

17.A traffic light ahead has been green for a long time. You should:

  1. Speed up to make the light
  2. Start slowing down and be ready to stop
  3. Change lanes
  4. Keep your speed, because green means go
Show answer

B. Start slowing down and be ready to stop

If a traffic light has been green for a long time, it will probably change before you get there. Start slowing down and be ready to stop.

CDL manual, section 2.4.1.

18.Mirror adjustment can only be checked accurately when:

  1. The trailer is straight
  2. The truck is moving
  3. It is dark
  4. The trailer is unhooked
Show answer

A. The trailer is straight

Check mirror adjustment before the start of any trip, with the trailer(s) straight. Adjust each mirror to show some part of the vehicle as a reference point.

CDL manual, section 2.4.2.

19.Watching your tires in the mirrors is one way to:

  1. Check your fuel level
  2. Measure tread depth
  3. See how fast you are going
  4. Spot a tire fire
Show answer

D. Spot a tire fire

Use the mirrors to keep an eye on your tires. It is one way to spot a tire fire. With open cargo, also watch for loose straps, ropes or chains and a flapping tarp.

CDL manual, section 2.4.2.

20.Why should you change lanes slowly and smoothly?

  1. To save fuel
  2. So the trailer does not sway in the wind
  3. So a driver you did not see has a chance to honk or get out of the way
  4. Because it is required on all highways
Show answer

C. So a driver you did not see has a chance to honk or get out of the way

Signal before changing lanes and change lanes slowly and smoothly. That way a driver you didn't see may have a chance to honk or avoid your vehicle.

CDL manual, section 2.5.1.

21.At dawn, at dusk, or in rain or snow, you should turn on:

  1. Your low-beam headlights
  2. Only your clearance lights
  3. Your high beams
  4. Your interior light
Show answer

A. Your low-beam headlights

Make yourself easier to see. Use the headlights, not just the identification or clearance lights, and use the low beams. High beams can bother people in the daytime as well as at night.

CDL manual, section 2.5.2.

22.You stop on a two-lane road with traffic in both directions. Where should you place your warning devices?

  1. All three 100 feet behind you
  2. Within 10 feet of the front or rear corners, plus 100 feet behind and 100 feet ahead
  3. 10, 100 and 200 feet behind you
  4. 500 feet ahead of you
Show answer

B. Within 10 feet of the front or rear corners, plus 100 feet behind and 100 feet ahead

On a two-lane road or undivided highway, place warning devices within 10 feet of the front or rear corners and 100 feet behind and ahead of the vehicle. The 10, 100 and 200 feet pattern is for a one-way or divided highway.

CDL manual, section 2.5.2.

23.While you carry warning triangles out to place them, you should hold them:

  1. Behind your back
  2. Over your head
  3. Between yourself and the oncoming traffic
  4. On the side away from traffic
Show answer

C. Between yourself and the oncoming traffic

Hold the triangles between yourself and the oncoming traffic for your own safety, so other drivers can see you.

CDL manual, section 2.5.2.

24.When you are parked at the side of the road, why shouldn't you rely on your taillights to warn others?

  1. Taillights are too bright
  2. Taillights are not required at night
  3. Taillights drain the battery
  4. Drivers may think your vehicle is moving normally and hit it
Show answer

D. Drivers may think your vehicle is moving normally and hit it

Turn on your four-way flashers when you pull off and stop, especially at night. Drivers have crashed into the rear of parked vehicles because they thought they were moving normally.

CDL manual, section 2.5.2.

All General Knowledge practice tests · Next: Practice Test 10 · Review my mistakes

Questions written by CDL Quiz Prep and checked against the CDL manual (November 2026). Manuals can differ slightly by state. Found a mistake? Report an error.