26 free CDL Air Brakes practice questions with answers and explanations. Choose an answer to check it right away and read why. You need at least 80% correct to pass the real test.
1.On newer vehicles, what does the parking brake control look like?
- A red, round knob
- A blue lever under the dash
- A green button on the steering wheel
- A yellow, diamond-shaped push-pull knob
Show answer
D. A yellow, diamond-shaped push-pull knob
Newer vehicles use a yellow diamond-shaped knob. Pull it out to put the parking (spring) brakes on and push it in to release them.
CDL manual, section 5.1.15.
2.What does a modulating control valve let you do?
- Change the governor cut-out pressure
- Drain the air tanks from the cab
- Turn the ABS off
- Apply the spring brakes gradually
Show answer
D. Apply the spring brakes gradually
The modulating valve is a spring-loaded dash lever. The more you move it, the harder the spring brakes come on, so you can control them if the service brakes fail.
CDL manual, section 5.1.15.
3.How do you park a vehicle that has a modulating control valve?
- Move the lever as far as it will go and lock it in place
- Leave the lever in the middle position
- Push the lever all the way in and release it
- Use only wheel chocks
Show answer
A. Move the lever as far as it will go and lock it in place
When parking, move the lever to its full travel and hold it there with the locking device.
CDL manual, section 5.1.15.
4.Some buses have dual parking control valves with a separate air tank to release the spring brakes. Why should you plan carefully when using it?
- It turns off the service brakes
- It can only be used above 55 psi
- It drains the main air tanks
- The separate tank only has enough air to release the brakes a few times
Show answer
D. The separate tank only has enough air to release the brakes a few times
The separate tank lets you move the vehicle in an emergency after main air is lost, but only a few times. Poor planning could leave you stopped in a dangerous place.
CDL manual, section 5.1.15.
5.Air-braked trucks, buses, trailers and converter dollies (other than truck tractors) must have ABS if they were built on or after what date?
- March 1, 1995
- March 1, 1997
- March 1, 1998
- March 1, 2000
Show answer
C. March 1, 1998
Truck tractors needed ABS from March 1, 1997. Other air-braked vehicles, including trailers and dollies, needed it from March 1, 1998.
CDL manual, section 5.1.16.
6.Where is the ABS malfunction lamp on a trailer?
- On the left side, at the front or rear corner
- On the instrument panel in the cab
- On the right side, next to the tail lights
- On the rear doors
Show answer
A. On the left side, at the front or rear corner
Tractors, trucks and buses have a yellow ABS lamp on the instrument panel. Trailers have it on the left side, front or rear corner.
CDL manual, section 5.1.16.
7.The ABS malfunction lamp stays on after the start-up bulb check. What may this mean?
- The ABS is working normally
- You may have lost ABS control at one or more wheels
- The air tanks are full
- The parking brake is on
Show answer
B. You may have lost ABS control at one or more wheels
On newer vehicles the lamp goes out soon after start-up. If it stays on, or comes on while driving, ABS may not be working at one or more wheels.
CDL manual, section 5.1.16.
8.How can you tell if an older towed unit has ABS?
- Check whether the trailer has a yellow parking knob
- Listen for a buzzer when you brake
- Look for a wig wag on the trailer
- Look under it for the electronic control unit and wheel speed sensor wires
Show answer
D. Look under it for the electronic control unit and wheel speed sensor wires
For trailers built before ABS was required, look under the vehicle for the ECU and for sensor wires coming from the back of the brakes.
CDL manual, section 5.1.16.
9.How does ABS change your normal braking capability?
- It does not increase or decrease it
- It doubles your braking power
- It always shortens stopping distance
- It reduces braking power to prevent skids
Show answer
A. It does not increase or decrease it
ABS is an addition to your normal brakes. It only acts when wheels are about to lock, helping you keep control.
CDL manual, section 5.1.16.
10.What is a dual air brake system?
- One air system with two compressors
- Two separate air brake systems that use a single set of brake controls
- An air system combined with hydraulic brakes
- A system with both spring brakes and wedge brakes
Show answer
B. Two separate air brake systems that use a single set of brake controls
Each half has its own tanks, hoses and lines. Both are worked by the same pedal and both supply air to a trailer if there is one.
CDL manual, section 5.2.
11.In a dual air brake system, which brakes does the primary system typically operate?
- Only the trailer brakes
- The regular brakes on the rear axle or axles
- Only the parking brakes
- The front axle brakes only
Show answer
B. The regular brakes on the rear axle or axles
The primary system typically works the rear axle brakes. The secondary system works the front axle and possibly one rear axle.
CDL manual, section 5.2.
12.Before driving a vehicle with a dual air system, what minimum pressure should you build up in both systems?
- 55 psi
- 85 psi
- 100 psi
- 150 psi
Show answer
C. 100 psi
Let the compressor build at least 100 psi in both the primary and secondary systems before you drive.
CDL manual, section 5.2.
13.While driving, the low air warning comes on because one half of a dual system is very low. What should you expect?
- The brakes will work normally until the tank is empty
- The spring brakes will release
- The other system will refill it automatically
- It will take longer to stop, so stop safely and have the brakes fixed
Show answer
D. It will take longer to stop, so stop safely and have the brakes fixed
With one system very low, either the front or the rear brakes are not working fully. Stop safely right away and get the system repaired.
CDL manual, section 5.2.
14.During the engine compartment check, what should you inspect on a belt-driven air compressor?
- The condition and tightness of the drive belt
- The alcohol level
- The slack adjuster travel
- The governor cut-in pressure
Show answer
A. The condition and tightness of the drive belt
If the compressor is belt-driven, check that the belt is in good condition and properly tight.
CDL manual, section 5.3.1.
15.Before checking slack adjusters by hand, what should you do?
- Park on level ground, chock the wheels and release the parking brakes
- Set the parking brakes and leave the engine running
- Drain the air tanks completely
- Pump the brake pedal until the warning comes on
Show answer
A. Park on level ground, chock the wheels and release the parking brakes
Chock the wheels so the vehicle cannot move, then release the parking brakes so the slack adjusters can move when you pull on them.
CDL manual, section 5.3.2.
16.When you pull hard on an s-cam slack adjuster, how much movement means it probably needs adjustment?
- More than about one-quarter inch
- More than about one inch
- More than about three inches
- Any movement at all
Show answer
B. More than about one inch
If a slack adjuster moves more than about one inch where the push rod attaches, it probably needs adjustment.
CDL manual, section 5.3.2.
17.What is the most common problem found in roadside inspections?
- Low tire pressure
- Broken lights
- Missing warning triangles
- Brakes out of adjustment
Show answer
D. Brakes out of adjustment
Out-of-adjustment brakes are the most common roadside inspection problem. Too much slack makes a vehicle very hard to stop.
CDL manual, section 5.3.2.
18.Vehicles built since what year have automatic slack adjusters?
- 1975
- 1988
- 1994
- 2001
Show answer
C. 1994
All vehicles built since 1994 have automatic slack adjusters. They adjust during full brake applications but must still be checked.
CDL manual, section 5.3.2.
19.A brake with an automatic slack adjuster is out of adjustment. What should you do?
- Adjust it by hand and keep driving as usual
- Ignore it, because it will adjust itself
- Release the parking brake and drive faster
- Take the vehicle to a repair facility as soon as possible
Show answer
D. Take the vehicle to a repair facility as soon as possible
An out-of-adjustment automatic adjuster points to a mechanical problem. Adjusting it by hand usually hides the problem; use that only as a temporary emergency measure.
CDL manual, section 5.3.2.
20.How long may a crack in a brake drum be?
- No longer than one half the width of the friction area
- No longer than one inch
- Any length, if the drum is not leaking
- No longer than the width of the friction area
Show answer
A. No longer than one half the width of the friction area
Drums or discs must not have cracks longer than half the width of the friction area.
CDL manual, section 5.3.2.
21.Which brake lining condition is NOT acceptable?
- Linings firmly attached
- Linings soaked with oil or grease
- Linings of normal thickness
- Linings that are dry
Show answer
B. Linings soaked with oil or grease
Linings must not be loose, soaked with oil or grease, or dangerously thin.
CDL manual, section 5.3.2.
22.When testing the governor, at about what pressures should the compressor start and stop pumping?
- Start at about 55 psi and stop at about 100 psi
- Start at about 100 psi and stop at about 125 psi
- Start at about 125 psi and stop at about 150 psi
- Start at about 20 psi and stop at about 45 psi
Show answer
B. Start at about 100 psi and stop at about 125 psi
Pumping should start around 100 psi and stop around 125 psi. Check the manufacturer's specifications.
CDL manual, section 5.3.3.
23.With the system fully charged, the engine off and the parking brake released, what is the maximum air loss for a single vehicle?
- Less than 2 psi in one minute
- Less than 4 psi in one minute
- Less than 6 psi in one minute
- Less than 10 psi in one minute
Show answer
A. Less than 2 psi in one minute
With the brakes released, a single vehicle should lose less than 2 psi in a minute; a combination vehicle less than 3 psi.
CDL manual, section 5.3.3.
24.With the engine off and the foot brake held down fully for one minute, what air loss is too much for a combination vehicle?
- More than 1 psi
- More than 2 psi
- More than 4 psi
- More than 8 psi
Show answer
C. More than 4 psi
With the brake applied, a loss of more than 4 psi in a minute is too much for a combination vehicle (more than 3 psi for a single vehicle). Find and fix the leak before driving.
CDL manual, section 5.3.3.
25.In a dual air system, how fast should pressure build from 85 to 100 psi with the engine at operating rpm?
- Within 3 minutes
- Within 5 minutes
- Within 10 seconds
- Within 45 seconds
Show answer
D. Within 45 seconds
Dual systems should build from 85 to 100 psi within 45 seconds. Larger-than-minimum tanks may take longer; check the manufacturer's specifications.
CDL manual, section 5.3.3.
26.How do you check that the spring brakes come on automatically?
- Pull the parking brake knob while driving at 5 mph
- Open the drain valves while the engine runs
- Fan off the air by stepping on and off the brake until the parking brake valve pops out
- Disconnect the compressor belt
Show answer
C. Fan off the air by stepping on and off the brake until the parking brake valve pops out
Keep reducing tank pressure with the pedal. The parking brake valve (and the tractor protection valve on a tractor-trailer) should pop out at the manufacturer's setting, 20-45 psi.
CDL manual, section 5.3.3.
All Air Brakes practice tests · Next: Practice Test 3 · Review my mistakes
Questions written by CDL Quiz Prep and checked against the CDL manual (November 2026). Manuals can differ slightly by state. Found a mistake? Report an error.