25 free CDL Air Brakes practice questions with answers and explanations. Choose an answer to check it right away and read why. You need at least 80% correct to pass the real test.
1.What are the three braking systems that make up an air brake system?
- Service brake, parking brake and emergency brake
- Foot brake, hand brake and engine brake
- Front brake, rear brake and trailer brake
- Drum brake, disc brake and wedge brake
Show answer
A. Service brake, parking brake and emergency brake
Air brakes combine a service brake for normal stops, a parking brake, and an emergency brake that uses parts of the other two when the system fails.
CDL manual, section 5 (introduction).
2.What does the air compressor do?
- It releases extra air when the pressure is too high
- It shows the driver how much air is in the tanks
- It removes water and oil from the air
- It pumps air into the air storage tanks
Show answer
D. It pumps air into the air storage tanks
The compressor fills the storage tanks (reservoirs) with air. It is driven by the engine through gears or a v-belt.
CDL manual, section 5.1.1.
3.If the air compressor has its own oil supply, what should you do before driving?
- Drain the compressor oil
- Run the engine for 10 minutes
- Add alcohol to the compressor
- Check the compressor oil level
Show answer
D. Check the compressor oil level
A compressor may use engine oil or have its own supply. If it has its own supply, check that oil level before you drive.
CDL manual, section 5.1.1.
4.At about what tank pressure does the governor stop the compressor from pumping air (the cut-out level)?
- 55 psi
- 100 psi
- 125 psi
- 150 psi
Show answer
C. 125 psi
The governor cuts the compressor out at around 125 psi. It lets the compressor start again at around 100 psi.
CDL manual, section 5.1.2.
5.At about what tank pressure does the governor let the compressor start pumping again (the cut-in level)?
- 55 psi
- 100 psi
- 125 psi
- 150 psi
Show answer
B. 100 psi
Cut-in is around 100 psi. When tank pressure falls to that level, the compressor starts pumping again.
CDL manual, section 5.1.2.
6.Why must air tanks be drained?
- Water and oil collect in the tanks, and water can freeze and cause brake failure
- Old air loses pressure and must be replaced each day
- Draining lowers the cut-out pressure of the governor
- The safety valve will not work if the tanks are full
Show answer
A. Water and oil collect in the tanks, and water can freeze and cause brake failure
Compressed air carries water and compressor oil, which settle in the bottom of the tanks. Water can freeze in cold weather and make the brakes fail.
CDL manual, section 5.1.4.
7.How often must you drain air tanks that have manual drain valves?
- At the end of each day of driving
- Once a week
- Only in cold weather
- Only when the low air warning comes on
Show answer
A. At the end of each day of driving
Manual drains are opened by a quarter turn or by pulling a cable. You must drain the tanks completely at the end of each driving day.
CDL manual, section 5.1.4.
8.What does an alcohol evaporator do in an air brake system?
- It cleans oil out of the air tanks
- It cools the air compressor
- It replaces the need for a safety valve
- It reduces the risk of ice in brake valves and other parts in cold weather
Show answer
D. It reduces the risk of ice in brake valves and other parts in cold weather
The evaporator puts alcohol into the air system so ice is less likely to form in cold weather. Ice inside the system can stop the brakes from working.
CDL manual, section 5.1.5.
9.Your air brake system has an alcohol evaporator but manual drain valves. What is true?
- You no longer need to drain the air tanks
- You only drain the tanks once a month
- You drain the tanks only when the alcohol container is empty
- You must still drain the air tanks every day
Show answer
D. You must still drain the air tanks every day
The evaporator does not remove water and oil. Unless the system has automatic drains, the tanks still need daily draining. Check and fill the alcohol container every day in cold weather.
CDL manual, section 5.1.5.
10.At what pressure is the safety relief valve usually set to open?
- 100 psi
- 125 psi
- 150 psi
- 175 psi
Show answer
C. 150 psi
The safety valve sits in the first tank the compressor fills. It is usually set to open at 150 psi to protect the system from too much pressure.
CDL manual, section 5.1.6.
11.The safety relief valve releases air while you are driving. What does this mean?
- Something is wrong and a mechanic should fix it
- The system is working normally
- The air tanks need to be drained
- The governor cut-in pressure is too low
Show answer
A. Something is wrong and a mechanic should fix it
The safety valve should only open when pressure is too high. If it releases air, there is a fault that a mechanic should repair.
CDL manual, section 5.1.6.
12.What are other names for the brake pedal in an air brake system?
- Relay valve or quick release valve
- Foot valve or treadle valve
- Slack adjuster or push rod
- Governor or cut-out valve
Show answer
B. Foot valve or treadle valve
The brake pedal is also called the foot valve or treadle valve. Pushing it harder applies more air pressure.
CDL manual, section 5.1.7.
13.Why should you avoid pressing and releasing the brake pedal when it is not needed?
- It wears out the brake drums
- It can let air out faster than the compressor can replace it
- It turns off the low air warning
- It makes the governor cut out early
Show answer
B. It can let air out faster than the compressor can replace it
Each release lets some compressed air out of the system. Fanning the pedal can drop pressure faster than the compressor refills it, and the brakes stop working if pressure gets too low.
CDL manual, section 5.1.7.
14.What is the most common type of foundation brake on commercial vehicles?
- Wedge brake
- Air-operated disc brake
- Hydraulic disc brake
- S-cam drum brake
Show answer
D. S-cam drum brake
Foundation brakes are the brakes at each wheel. The s-cam drum brake is the most common; wedge and disc brakes are less common.
CDL manual, section 5.1.8.
15.In an s-cam brake, what twists the brake camshaft when you press the brake pedal?
- The push rod moves the slack adjuster
- The governor pushes the cam directly
- The spring brake pulls the cam
- The wheel speed sensor turns the cam
Show answer
A. The push rod moves the slack adjuster
Air enters the brake chamber and pushes the rod out. The rod moves the slack adjuster, which twists the camshaft and turns the s-cam to press the shoes against the drum.
CDL manual, section 5.1.8.
16.In an air-operated disc brake, what part clamps the rotor between the brake pads?
- A power screw
- An s-cam
- A wedge
- A wig wag
Show answer
A. A power screw
Disc brakes use a brake chamber and slack adjuster like s-cam brakes, but the slack adjuster turns a power screw that clamps the rotor, like a large c-clamp.
CDL manual, section 5.1.8.
17.What does a supply pressure gauge tell you?
- How much air pressure you are applying to the brakes
- How much air pressure is in the air tanks
- How fast the compressor is turning
- How hot the brake drums are
Show answer
B. How much air pressure is in the air tanks
Every vehicle with air brakes has a supply pressure gauge connected to the tanks. A dual system has a gauge for each half, or one gauge with two needles.
CDL manual, section 5.1.9.
18.Your application pressure gauge shows you need more and more pressure to hold the same speed. What does this mean?
- The air tanks are overfilled
- The governor needs to cut in
- The ABS is working normally
- The brakes are fading, so slow down and use a lower gear
Show answer
D. The brakes are fading, so slow down and use a lower gear
Needing more application pressure for the same speed means brake fade. It can also come from brakes out of adjustment, air leaks or mechanical problems.
CDL manual, section 5.1.10.
19.Before tank pressure falls below what level must the low air pressure warning come on?
- 20 psi
- 45 psi
- 55 psi
- 85 psi
Show answer
C. 55 psi
A visible warning, usually a red light and sometimes a buzzer, must come on before tank pressure drops below 55 psi.
CDL manual, section 5.1.11.
20.What is a "wig wag"?
- A light that flashes when the ABS fails
- A valve that drains the air tanks automatically
- A switch that turns on the brake lights
- A mechanical arm that drops into view when air pressure falls below 55 psi
Show answer
D. A mechanical arm that drops into view when air pressure falls below 55 psi
A wig wag is a low air pressure warning device. The arm drops into the driver's view when pressure falls below 55 psi.
CDL manual, section 5.1.11.
21.On large buses, at what pressure do low air warning devices commonly signal?
- 20-30 psi
- 55-60 psi
- 80-85 psi
- 120-125 psi
Show answer
C. 80-85 psi
Large buses commonly have low pressure warnings set at 80-85 psi, higher than the 55 psi minimum.
CDL manual, section 5.1.11.
22.An older vehicle has a front brake limiting valve with a "normal" and "slippery" control. Where should the control be?
- In the "normal" position
- In the "slippery" position on wet roads
- In the "slippery" position at all times
- It does not matter
Show answer
A. In the "normal" position
The "slippery" setting cuts front brake pressure by half and reduces stopping power. Front wheel braking is good in all conditions, so keep it on "normal".
CDL manual, section 5.1.13.
23.What holds spring brakes off while you are driving?
- Hydraulic fluid
- Air pressure
- The slack adjusters
- The brake pedal
Show answer
B. Air pressure
Powerful springs are held back by air pressure. If the air is removed, by the parking control or by a leak, the springs put the brakes on.
CDL manual, section 5.1.14.
24.In a tractor or straight truck, at what air pressure range do the spring brakes come fully on?
- 0-10 psi
- 20-45 psi
- 55-60 psi
- 80-85 psi
Show answer
B. 20-45 psi
Spring brakes come fully on between 20 and 45 psi, typically 20 to 30 psi. Stop safely as soon as the low air warning comes on instead of waiting for them.
CDL manual, section 5.1.14.
25.Why should you never push the brake pedal down when the spring brakes are on?
- It releases the spring brakes
- It turns off the low air warning
- It drains the air tanks
- The combined force of the springs and the air pressure can damage the brakes
Show answer
D. The combined force of the springs and the air pressure can damage the brakes
Some systems prevent it, but not all, and those that do may not always work. Make it a habit not to press the pedal while the spring brakes are applied.
CDL manual, section 5.1.15.
All Air Brakes practice tests · Next: Practice Test 2 · Review my mistakes
Questions written by CDL Quiz Prep and checked against the CDL manual (November 2026). Manuals can differ slightly by state. Found a mistake? Report an error.