25 free CDL Combination Vehicles practice questions with answers and explanations. Choose an answer to check it right away and read why. You need at least 80% correct to pass the real test.
1.What might it mean if there is space between the upper and lower fifth wheel?
- The fifth wheel needs more grease
- The kingpin may be on top of the closed jaws, and the trailer could come loose
- The trailer is loaded too heavily
- The landing gear is not raised
Show answer
B. The kingpin may be on top of the closed jaws, and the trailer could come loose
Space may mean the kingpin is on top of the closed fifth wheel jaws. The trailer would come loose very easily.
CDL manual, section 6.4.1.
2.When the trailer is coupled correctly, what do the fifth wheel jaws close around?
- The head of the kingpin
- The glide plate
- The shank of the kingpin
- The landing gear
Show answer
C. The shank of the kingpin
Look into the back of the fifth wheel and make sure the jaws have closed around the shank of the kingpin.
CDL manual, section 6.4.1.
3.After coupling, where should the safety latch be?
- Under the fifth wheel plate
- Removed and stored in the cab
- In the open position
- In position over the locking lever
Show answer
D. In position over the locking lever
Check that the locking lever is in the lock position and the safety latch is in position over it.
CDL manual, section 6.4.1.
4.How should you begin raising the trailer landing gear?
- In the low gear range, then switch to high once it is free of weight
- In the high gear range, then switch to low
- With the tractor moving slowly forward
- Only after the air lines are disconnected
Show answer
A. In the low gear range, then switch to high once it is free of weight
Use the low gear range to begin raising the landing gear. Once it is free of weight, switch to the high gear range.
CDL manual, section 6.4.1.
5.How far should you raise the landing gear before driving?
- Just until it lifts off the pavement
- All the way up
- Halfway up
- It depends on the load
Show answer
B. All the way up
Raise it all the way up. Landing gear left part way up may catch on railroad tracks or other things.
CDL manual, section 6.4.1.
6.After raising the landing gear, what clearance should you check?
- Between the trailer and the ground
- Between the glad hands
- Between the rear of the tractor frame and the landing gear
- Between the fifth wheel and the cab
Show answer
C. Between the rear of the tractor frame and the landing gear
Check that the tractor frame will not hit the landing gear in a sharp turn, and that the tractor tires clear the trailer nose.
CDL manual, section 6.4.1.
7.Why should the tractor be lined up with the trailer when you uncouple?
- To make the air lines easier to reach
- To keep the trailer level
- To save fuel
- Pulling out at an angle can damage the landing gear
Show answer
D. Pulling out at an angle can damage the landing gear
Have the tractor lined up with the trailer. Pulling out at an angle can damage the landing gear.
CDL manual, section 6.4.2.
8.During uncoupling, why do you back up gently and set the parking brakes while pushing against the kingpin?
- To ease pressure on the locking jaws so the release handle is easier to pull
- To lower the trailer onto its landing gear
- To check the trailer brakes
- To drain the air tanks
Show answer
A. To ease pressure on the locking jaws so the release handle is easier to pull
Backing gently eases pressure on the fifth wheel locking jaws, and the parking brakes hold the rig with the pressure off.
CDL manual, section 6.4.2.
9.When uncoupling a loaded trailer, what should you do after the landing gear touches the ground?
- Stop cranking right away
- Turn the crank a few extra turns in low gear to lift some weight off the tractor
- Lift the trailer completely off the fifth wheel
- Raise the landing gear again slightly
Show answer
B. Turn the crank a few extra turns in low gear to lift some weight off the tractor
A few extra turns lift some weight off the tractor, which makes it easier to unlatch and to couple next time. Do not lift the trailer off the fifth wheel.
CDL manual, section 6.4.2.
10.How should you hang the electrical cable after disconnecting it?
- Plug up
- Wrapped around the glad hands
- Plug down, to keep moisture out
- On the ground behind the tractor
Show answer
C. Plug down, to keep moisture out
Hang the electrical cable with the plug down to prevent moisture from entering it.
CDL manual, section 6.4.2.
11.When you first pull the tractor out from under the trailer, where should you stop?
- After the tractor is fully clear
- Before the fifth wheel comes out
- As soon as the kingpin unlocks
- With the tractor frame still under the trailer
Show answer
D. With the tractor frame still under the trailer
Stop with the tractor frame under the trailer. This keeps the trailer from falling if the landing gear collapses or sinks.
CDL manual, section 6.4.2.
12.When coupling a gooseneck trailer, what must you attach after latching the clamp?
- The safety chains
- The dummy couplers
- The fifth wheel release handle
- A wheel chock
Show answer
A. The safety chains
Attach the safety chains. The manual notes that all trailers are required by law to have safety chains.
CDL manual, section 6.4.7.
13.What can happen if a pintle hook latch is not locked correctly?
- The trailer brakes stay on
- The trailer can separate from the vehicle
- The trailer lights will not work
- The trailer off-tracks more
Show answer
B. The trailer can separate from the vehicle
Failure to lock the latch correctly can let the trailer separate from the vehicle, which can cause death or serious injury.
CDL manual, section 6.4.3.
14.During a walk-around inspection, what should you check about a sliding fifth wheel's position?
- That it is as far back as possible
- That it is unlocked so it can move in turns
- That it is not so far forward that the tractor frame hits the landing gear or the cab hits the trailer in turns
- That it is centered over the drive tires only
Show answer
C. That it is not so far forward that the tractor frame hits the landing gear or the cab hits the trailer in turns
Check that the sliding fifth wheel is not so far forward that the tractor frame will hit the landing gear, or the cab hit the trailer, during turns.
CDL manual, section 6.5.1.
15.What should you check on the landing gear during a walk-around inspection?
- That it is lowered halfway
- That it touches the ground
- That the crank handle is removed
- That it is fully raised and the crank handle is in place and secured
Show answer
D. That it is fully raised and the crank handle is in place and secured
Landing gear should be fully raised, with no missing or damaged parts, and the crank handle in place and secured.
CDL manual, section 6.5.1.
16.During inspection, what should you check about the air lines to the trailer?
- They are connected, not leaking, secured, and have enough slack for turns
- They are pulled tight so they cannot move
- They are crossed so the brakes stay on
- They rest on the catwalk with no support
Show answer
A. They are connected, not leaking, secured, and have enough slack for turns
Air lines should be properly connected to the glad hands, with no leaks, properly secured with enough slack for turns, and undamaged.
CDL manual, section 6.5.1.
17.How can you check that air flows to all trailers?
- Watch the air gauge while driving
- Open the emergency line shut-off valve at the rear of the last trailer and listen for air escaping
- Pull out the trailer air supply knob and listen
- Drain the air tanks on each trailer
Show answer
B. Open the emergency line shut-off valve at the rear of the last trailer and listen for air escaping
With the trailer air supply knob pushed in, open the emergency line valve at the rear of the last trailer. Escaping air shows the system is charged. Then close it and check the service line the same way.
CDL manual, section 6.5.2.
18.You hear no air escaping at the rear of the last trailer during the air flow check. What should you check?
- The tire pressure
- The ABS lamp
- That the shut-off valves on the trailers and dollies are open
- That the landing gear is raised
Show answer
C. That the shut-off valves on the trailers and dollies are open
If you don't hear air from both lines, check that the shut-off valves on the trailers and dollies are in the open position.
CDL manual, section 6.5.2.
19.How do you test the tractor protection valve?
- Pull out the air supply knob while driving
- Disconnect the service line while the engine runs
- Apply the trailer hand valve and pull forward
- With the engine off, step on and off the brake pedal to lower the pressure, and check that the air supply control pops out
Show answer
D. With the engine off, step on and off the brake pedal to lower the pressure, and check that the air supply control pops out
Charge the trailer system, shut the engine off, and pump the brake pedal. The air supply control should pop out, usually between 20 and 45 psi.
CDL manual, section 6.5.2.
20.Why does it matter if the tractor protection valve does not work right?
- A hose or trailer brake leak could drain all the air from the tractor
- The trailer would not get any air at all
- The ABS would turn off
- The trailer lights would fail
Show answer
A. A hose or trailer brake leak could drain all the air from the tractor
If the valve doesn't work right, an air hose or trailer brake leak could drain all the tractor's air, bringing on the emergency brakes with possible loss of control.
CDL manual, section 6.5.2.
21.How do you test the trailer emergency brakes?
- Pump the brake pedal until the alarm sounds
- Charge the system, then pull out the trailer air supply control and pull gently against the trailer
- Use the trailer hand valve at highway speed
- Disconnect the service line and drive forward
Show answer
B. Charge the system, then pull out the trailer air supply control and pull gently against the trailer
Charge the trailer brakes and check that the trailer rolls freely. Then pull out the air supply control and pull gently with the tractor to check the brakes are on.
CDL manual, section 6.5.2.
22.How do you test the trailer service brakes?
- Push in the air supply knob and listen
- Pull out the air supply knob at speed
- Move forward slowly and apply the trailer brakes with the hand control
- Drain the trailer air tanks
Show answer
C. Move forward slowly and apply the trailer brakes with the hand control
With normal air pressure and the parking brakes released, move slowly forward and apply the trailer brakes with the hand control. You should feel them come on.
CDL manual, section 6.5.2.
23.In normal driving, how should the trailer brakes be applied?
- With the trailer hand valve
- By pulling the air supply knob
- With the tractor parking brake
- With the foot brake pedal
Show answer
D. With the foot brake pedal
Test the trailer brakes with the hand valve, but control them in normal driving with the foot pedal, which applies the service brakes at all wheels.
CDL manual, section 6.5.2.
24.How does the length of a vehicle affect off-tracking?
- Longer vehicles off-track more
- Shorter vehicles off-track more
- Length makes no difference
- Only the tractor off-tracks
Show answer
A. Longer vehicles off-track more
Longer vehicles off-track more, and the rear wheels of the last trailer off-track the most.
CDL manual, section 6.1.6.
25.When backing a trailer, what are pull-ups for?
- To test the trailer brakes
- To check the fifth wheel lock
- To warm up the engine
- To reposition your vehicle as needed
Show answer
D. To reposition your vehicle as needed
When backing a trailer, make pull-ups to reposition your vehicle as needed. Back slowly so you can correct before you get too far off course.
CDL manual, section 6.1.7.
All Combination Vehicles practice tests · Review my mistakes
Questions written by CDL Quiz Prep and checked against the CDL manual (November 2026). Manuals can differ slightly by state. Found a mistake? Report an error.